QUESTION 11
Which role does the router ID (RID) have in the BGP route selection process?
A. The router ID is evaluated immediately after MED to determine route preference
B. The router ID is evaluated last in the route selection process
C. The router ID is evaluated after the cluster length and a lower router ID is chosen
D. The router ID is evaluated after analyzing the IGP metric cost
Answer: B
QUESTION 12
You are logged into a router and have navigated to the [edit routing-options] level of the hierarchy. You have been asked to create a static route that will use 43 18 7 1 as its primary next-hop and 76 1310 2 as its secondary next-hop.
Which command correctly configures this setup?
A. set static route 0/0 76.13.10.2 qualified-next-hop 43.18.7.1 pref 10
B. set static route 0/0 next-hop 43.18.7.1 secondary-next-hop 76.13.10.2 preference 10
C. set static route 0/0 next-hop [76.13.10.2 10.10.10.5] pref 10
D. set static route 0/0 next-hop 43.18.7.1 qualified-next-hop 76.13.10.2 preference 10
Answer: D
QUESTION 13
Click the Exhibit button. Referring to the network illustrated in the exhibit, how does router A reach destinations in area 49.2222?
A. Router A will use the routes from area 49.2222; it learns from router B
B. Router A will see the attached bit from router B and create a default route
C. Router A must have a default route manually configured
D. Router A will receive a default route in the IS-IS update from router B
Answer: B
QUESTION 14
You have recently implemented a graceful Routing-Engine switchover (GRES) and want to further reduce down time if a Routing Engine (RE) failure occurs.
Which two features can be configured on this device to reduce its downtime in this situation? (Choose two)
A. VRRP
B. GR
C. BFD
D. NSR
Answer: BD
QUESTION 15
Which BGP state denotes a fully operational session?
A. Established
B. Active
C. Operational
D. Connect
Answer: A
QUESTION 16
Click the Exhibit button. You work for the regional Internet service provider shown in the exhibit You have a partial BGP table and are receiving a 10 100/16 route from your upstream ISP You have been asked to configure a default route that can be sent to your downstream customer This route should forward customer traffic toward your upstream Tier 11SP as long as the 10.100/16 route is present.
What would accomplish this goal?
A. Create and announce an aggregate default route
B. Create and announce a static default route with a next-hop of discard
C. Create and announce a static default route with a next-hop of reject
D. Create and announce a generated default route
E. Create an advertise-map with exist-map
Answer: D
QUESTION 17
You have been asked to configure an IPv6 address for a group of interfaces that could belong on different routers. If a packet is sent to that address, it should be received by all routers in the group.
Which address type would be suited for these requirements?
A. Unicast
B. Multicast
C. Anycast
D. Broadcast
Answer: B
QUESTION 18
Click the Exhibit button. In the exhibit, OSPF routers R1, R2, R3, and R4 come up, in order, at 1-minute intervals. Which router will be the designated router?.
A. R1
B. R2
C. R3
D. R4
Answer: A
QUESTION 19
What is the function of the hop limit field in the IPv6 header?
A. It limits the diameter of the network to 20 hops
B. It sets the number of hops in the network to be equal to the MPLS header time-to-live (TTL)
C. It replaces the time-to-live (TTL) field in IPv4
D. It represents future extensibility to the protocol
Answer: C
QUESTION 20
You have been asked to define a default gateway for traffic leaving a router. This route should use interface so-0/0/0 as its next-hop.Which type of route would be suited for this scenario?
A. a static route
B. a generated route
C. a martian route
D. an aggregate route
Answer: A
If you want to pass Juniper JN0-360 successfully, donot missing to read latest lead2pass Juniper JN0-360 practice exams.
If you can master all lead2pass questions you will able to pass 100% guaranteed.