2014 Latest 100% Pass Guaranteed Juniper JN0-360 Practice Tests (121-130)

By | May 7, 2014

QUESTION 121
Which two events could cause the BGP Active state to appear? (Choose two.)

A.    The local router does not have a route to the peer device.
B.    The local router failed to establish a TCP connection with the peer device.
C.    A firewall is stopping all UDP packets.
D.    The BGP configuration is incomplete.

Answer: BD

QUESTION 122
Click the Exhibit button. The policy shown in the exhibit has been configured and installed on your router.

image
What is the result of applying this policy?

A.    The 172.18.1.0/24 network will be redistributed into OSPF as an external route.
B.    The 172.18.1.0/24 network will be redistributed into OSPF as an internal route.
C.    The 172.18.1.0/32 network will be redistributed into OSPF as an external route.
D.    The 172.18.1.0/32 network will be redistributed into OSPF as an internal route.

Answer: A

QUESTION 123
Which type of router can provide connectivity between areas in an IS-IS domain?

A.    a Level 1 router with adjacencies within a single area
B.    a Level 2 router with adjacencies in more than one area
C.    an area border router with adjacencies in more than one area
D.    a Level 2 router with adjacencies in a single area

Answer: B

QUESTION 124
You have been asked to provision a service provider’s network to accommodate Layer 3 VPNs as defined in RFC 4364.Which three tasks must be performed before the provider network is ready to carry VPN traffic? (Choose three.)

A.    All Juniper Networks PE routers must be configured with an appropriate router-ID unique to the VPN.
B.    All Juniper Networks PE routers must be configured with an appropriate route-target unique to the VPN.
C.    All Juniper Networks PE routers must be configured with a routing-instance of type forwarding.
D.    All Juniper Networks PE routers must be configured with a routing-instance of type vrf.
E.    All Juniper Networks PE routers must be configured with a routing-instance containing the CE- facing
interface.

Answer: BDE

QUESTION 125
By default, which BGP attribute is only compared when two route advertisements are received from the same neighboring AS?

A.    MED
B.    AS-Path
C.    Communities
D.    Next Hop

Answer: A

QUESTION 126
Click the Exhibit button. Referring to the exhibit, what must be true of the vlan_100 bridge domain?

image
A.    vlan_100 has at least one Ethernet interface assigned to it.
B.    vlan_100 does not have an Ethernet interface assigned to it.
C.    vlan_100 might have an active Ethernet interface assigned to it.
D.    vlan_100 does not have an active Ethernet interface assigned to it.

Answer: A

QUESTION 127
An Ethernet bridge is configured such that all interfaces are in a single broadcast domain.Which two tasks does the bridge perform in response to receiving a frame with an unknown unicast destination MAC address? (Choose two.)

A.    It drops the frame.
B.    It floods the frame out of all interfaces except the one on which is was received.
C.    It learns the destination MAC address.
D.    It learns the source MAC address.

Answer: BD

QUESTION 128
You have configured multiple IP-IP tunnels across your network to provide connectivity to remote sites.Which technique is used to help the IP endpoints in your network determine the optimal packet size to send across your tunnels?

A.    path MTU discovery
B.    fragmentation discovery
C.    end-to-end MTU discovery
D.    packet throughput discovery

Answer: A

QUESTION 129
You are asked to design a Layer 2 VPN service between service provider networks that needs Ethernet transport capabilities. The VPN should support two or three endpoints. Which Layer 2 VPN technology should you propose?

A.    LDP-signaled VPLS
B.    BGP-signaled VPLS, using the RFC 4448 Layer 2 frame format
C.    LDP Layer 2 circuit, using the RFC 4448 Layer 2 frame format
D.    BGP Layer 2 VPN

Answer: B

QUESTION 130
You are adding nonforwarding route reflectors to your network. Which three actions ensure that VPN routes are advertised properly? (Choose three.)

A.    Use rib-groups to add IGP routes to inet.3 and/or inet6.3 on the route reflectors.
B.    Add MPLS LSPs between the route reflectors and their client routers.
C.    Add the route reflectors to the same IGP domain as their clients.
D.    Use rib-groups to add VPN routes to inet.0 and/or inet6.0 on the route reflectors.
E.    Add a static default route to inet.3 and/or inet6.3 on the route reflectors.

Answer: ABE

If you want to pass Juniper JN0-360 successfully, donot missing to read latest lead2pass Juniper JN0-360 dumps.
If you can master all lead2pass questions you will able to pass 100% guaranteed.

http://www.lead2pass.com/JN0-360.html