2014 Latest 100% Pass Guaranteed Juniper JN0-360 Practice Tests (51-60)

By | April 30, 2014

QUESTION 51
You want to configure support for an IPv6 environment In which hierarchy would you configure an OSPF area?

A.    [edit protocols ospf-v6]
B.    [edit protocols ipv6-ospf
C.    [edit protocols ipv6J
D.    [edit protocols ospf3]

Answer: D

QUESTION 52
Which action does the local router take after sending a Notification message to a remote peer?

A.    It begins to send route update information
B.    It tears down the TCP session and attempts to re-establish it
C.    It waits for the remote router to acknowledge that it is ready to receive routes
D.    It changes its local state to Established

Answer: B

QUESTION 53
You have been asked to configure and assign addresses for your IPv6 routers in your network using dynamic assignment of DNS servers. You do not want the MAC address included as part of the IPv6 address.
Which method of address assignment would accomplish these requirements?

A.    DHCP
B.    stateless auto configuration
C.    DHCPv6
D.    stateful auto configuration

Answer: C

QUESTION 54
Click the Exhibit button. Which two topologies shown in the exhibit would require the use of a spanning-tree protocol? (Choose two)

image
A.    ring
B.    tree
C.    star
D.    mesh

Answer: AD

QUESTION 55
Which three functions are performed by an OSPF area border router (ABR)? (Choose three)

A.    flooding Summary LSAs to connected areas
B.    flooding ASBR Summary LSAs to connected areas
C.    generating all Router LSAs for connected neighbors
D.    performing summarization on routes headed to Area 0
E.    flooding NSSA External LSAs to Area 0

Answer: ABD

QUESTION 56
A customer configures a bridge domain using a VLAN ID of 222.
Which configuration will allow for the switch to potentially look at the IP header of incoming frames tagged with a VLAN ID of 222?

image

A.    Option A
B.    Option B
C.    Option C
D.    Option D

Answer: D

QUESTION 57
Your area border router (ABR) receives type 1.2 and 5 link-state advertisements (LSAs) from a non-backbone area.
What would the ABR do with the information learned from the non-backbone area?

A.    The ABR will generate type 2 and 3 LSAs and flood type 5 LSAs to the backbone area
B.    The ABR will generate only type 3 LSAs and flood only type 5 LSAs to the backbone area
C.    The ABR will generate type 3 and 4 LSAs. And flood type 5 LSAs to the backbone area
D.    The ABR will generate only type 4 LSAs and flood only type 5 LSAs to the backbone area

Answer: B

QUESTION 58
Which label operation is performed by an MPLS ingress router?

A.    Pop
B.    Push
C.    Replace
D.    Swap

Answer: B

QUESTION 59
An RSVP LSP in your network is operational but you are receiving complaints about network throughput across the LSP. You suspect that the RSVP bandwidth was omitted from the router configuration.
Which operational mode command will help you verify your suspicions?

A.    show interfaces terse
B.    show mpls lsp extensive
C.    show rsvp neighbor detail
D.    show rsvp bandwidth

Answer: B

QUESTION 60
After configuring OSPF between two routers you check for an adjacency. You see that the adjacencies are not coming up on an Ethernet segment.
What are two reasons that would cause this situation? (Choose two)

A.    You have a mismatched IP subnet/mask
B.    Your hello timer intervals are mismatched
C.    You are not using the same Junos version on each side
D.    You priority values are mismatched

Answer: AB

If you want to pass Juniper JN0-360 successfully, donot missing to read latest lead2pass Juniper JN0-360 practice tests.
If you can master all lead2pass questions you will able to pass 100% guaranteed.

http://www.lead2pass.com/JN0-360.html