Cisco Certified Network Associate: 640-802 Exam
640-802 Questions & Answers
Exam Code: 640-802
Exam Name: Cisco Certified Network Associate
Q & A: 660 Q&As
QUESTION 1 An administrator is unsuccessful in adding VLAN 50 to a switch. While troubleshooting the problem, the administrator views the output of the show vtp status command, which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database? (Choose two.) A. Switch(config-if)# switchport access vlan 50 B. Switch(vlan)# vtp server C. Switch(config)# config-revision 20 D. Switch(config)# vlan 50 name Tech E. Switch(vlan)# vlan 50 F. Switch(vlan)# switchport trunk vlan 50 Answer: BE QUESTION 2 Refer to the exhibit. Based on the information given, which switch will be elected root bridge and why? A. Switch A, because it has the lowest MAC address B. Switch A, because it is the most centrally located switch C. Switch B, because it has the highest MAC address D. Switch C, because it is the most centrally located switch E. Switch C, because it has the lowest priority F. Switch D, because it has the highest priority Answer: E QUESTION 5 Refer to the exhibit. A problem with network connectivity has been observed. It is suspected that the cable connected to switch port Fa0/9 on Switch1 is disconnected. What would be an effect of this cable being disconnected? A. Host B would not be able to access the server in VLAN9 until the cable is reconnected. B. Communication between VLAN3 and the other VLANs would be disabled. C. The transfer of files from Host B to the server in VLAN9 would be significantly slower. D. For less than a minute, Host B would not be able to access the server in VLAN9. Then normal network function would resume. Answer: D QUESTION 8 Host 1 is trying to communicate with Host 2. The e0 interface on Router C is down. Which of the following are true? (Choose two.) A. Router C will use ICMP to inform Host 1 that Host 2 cannot be reached. B. Router C will use ICMP to inform Router B that Host 2 cannot be reached. C. Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached. D. Router C will send a Destination Unreachable message type. E. Router C will send a Router Selection message type. F. Router C will send a Source Quench message type. Answer: AD QUESTION 9 Refer to the exhibit. After a RIP route is marked invalid on Router_1, how much time will elapse before that route is removed from the routing table? A. 30 seconds B. 60 seconds C. 90 seconds D. 180 seconds E. 240 seconds Answer: E QUESTION 10 Refer to the exhibit. A network associate has configured the internetwork that is shown in the exhibit, but has failed to configure routing properly. Which configuration will allow the hosts on the Branch LAN to access resources on the HQ LAN with the least impact on router processing and WAN bandwidth? A. HQ(config)# ip route 192.168.1.0 255.255.255.0 192.168.2.5 Branch(config)# ip route 172.16.25.0 255.255.255.0 192.168.2.6 B. HQ(config)# router rip HQ(config-router)# network 192.168.2.0 HQ(config-router)# network 172.16.0.0 Branch(config)# router rip Branch(config-router)# network 192.168.1.0 Branch(config-router)# network 192.168.2.0 C. HQ(config)# router eigrp 56 HQ(config-router)# network 192.168.2.4 HQ(config-router)# network 172.16.25.0 Branch(config)# router eigrp 56 Branch(config-router)# network 192.168.1.0 Branch(config-router)# network 192.168.2.4 D. HQ(config)# router ospf 1 HQ(config-router)# network 192.168.2.4 0.0.0.3 area 0 HQ(config-router)# network 172.16.25.0 0.0.0.255 area 0 Branch(config)# router ospf 1 Branch(config-router)# network 192.168.1.0 0.0.0.255 area 0 Answer: A QUESTION 11 Which additional configuration step is necessary in order to connect to an access point that has SSID broadcasting disabled? A. Set the SSID value in the client software to public. B. Configure open authentication on the AP and the client. C. Set the SSID value on the client to the SSID configured on the AP. D. Configured MAC address filtering to permit the client to connect to the AP. Answer: C QUESTION 12 What is the default administrative distance of the OSPF routing protocol? A. 90 B. 100 C. 110 D. 120 E. 130 F. 170 Answer: C QUESTION 13 A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information? A. Router# show ip eigrp adjacency B. Router# show ip eigrp topology C. Router# show ip eigrp interfaces D. Router# show ip eigrp neighbors Answer: D QUESTION 14 All WAN links inside the ABC University network use PPP with CHAP for authentication security. Which command will display the CHAP authentication process as it occur between two routers in the network? A. show chap authentication B. show interface serial0 C. debug ppp authentication D. debug chap authentication E. show ppp authentication chap Answer: C … http://www.lead2pass.com/640-802.html