[Full Version] Free Lead2pass Cisco 200-401 PDF Dumps With New Update Exam Questions (41-50)

By | December 22, 2016

2016 December Cisco Official New Released 200-401 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

The Cisco 200-401 exam is a very hard exam to successfully pass. Here you will find free Lead2pass Cisco practice sample exam test questions that will help you prepare in passing the 200-401 exam. Lead2pass Guarantees you 100% pass exam 200-401.

Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/200-401.html

You are troubleshooting a connectivity problem and want to isolate the problem. You suspect that a router on the route to an unreachable network is at fault. Which command would you issue to see where the packets stop?

A.    router#ping
B.    router#tracert
C.    router#show ip route
D.    router#show cdp neighbors
E.    router#traceroute

Answer: E

The network administrator is using a Windows PC application that is called putty.exe for remote communication to a switch for network troubleshooting. Which two protocols could be used during this communication? (Choose two).

A.    SNMP
B.    HTTP
C.    Telnet
D.    RMON
E.    SSH

Answer: CE

What is the leading cause of fiber-optic link failure?

A.    contaminants
B.    crushed fiber
C.    poor testing practices
D.    bad connectors

Answer: A

A network administrator has subnetted the network using a subnet mask of A duplicate IP address of has accidentally been configured on a workstation in the network. The technician on the plant floor must assign this workstation a new IP address within that same subnetwork. Which address should be assigned to the workstation?


Answer: B

What are two recommended tools or commands that allow you to troubleshoot connectivity between two devices in different IP networks? (Choose two.)

A.    show interface status
B.    show spanning-tree
C.    ping
D.    show interfaces gigabitEthernet x/y switchport
E.    traceroute
F.    show interface

Answer: CE

What are two symptoms of duplex mismatch? (Choose two.)

A.    Ping does not return from one direction versus the other direction.
B.    Communication is slow and locks up.
C.    Speed is seen equally slow in both directions.
D.    The half-duplex side sees frame sequence errors or runt frames.
E.    The full-duplex side sees CRC errors.

Answer: BD

With a Cisco IE 2000 switch, what does a port status LED indicate when it is alternating green and amber?

A.    The port is sending or receiving data.
B.    A link is present.
C.    No link is present.
D.    There is a link fault.
E.    The port is not forwarding.

Answer: D

Which two ports does EtherNet/IP use to communicate? (Choose two.)

A.    TCP 44818
B.    UDP 44818
C.    TCP 502
D.    UDP 502
E.    TCP 2222
F.    UDP 2222

Answer: AF

Which prompt is used to configure parameters for the Ethernet ports of an industrial switch?

A.    Switch(config-if)#
B.    Switch(config-if-ind)#
C.    Switch(config-line)#
D.    Switch(config-ind)#
E.    Switch(config-vlan)#

Answer: A

EtherNet/IP is an Ethernet implementation of which protocol?

A.    CIP
B.    Industrial Protocol
C.    DeviceNet
D.    ControlNet

Answer: A

Lead2pass new released premium 200-401 exam dumps guarantee you a 100% exam success or we promise full money back! Download Cisco 200-401 exam dumps full version from Lead2pass instantly!

200-401 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDUjMxZHpSYkRSMmM

2016 Cisco 200-401 exam dumps (All 70 Q&As) from Lead2pass:

http://www.lead2pass.com/200-401.html [100% Exam Pass Guaranteed]