[Full Version] New Lead2pass 640-916 Dumps PDF Version Released For Free Downloading (121-140)

By | November 9, 2016

2016 November Cisco Official New Released 640-916 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

Lead2pass is ready to provide Cisco candidates with 640-916 exam dumps which can be very helpful for getting Cisco certification, which means that candidates can easily get access to the services of Cisco 640-916 exam dumps, which will assure them 100% passing success rate. With Lead2pass 640-916 exam dumps, it will be easy to pass your 640-916 exam at your first time.

Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/640-916.html

QUESTION 121
What two interface types can be used for switch-to-switch communications? (Choose two.)

A.    E Port
B.    F Port
C.    N Port
D.    TE Port
E.    FL Port

Answer: AD

QUESTION 122
What two protocols can be used to connect to storage arrays on a converged Ethernet/IP network? (Choose two.)

A.    FCoE
B.    Fibre Channel
C.    ISCSI
D.    InfiniBand
E.    FabricPath

Answer: AC

QUESTION 123
An engineer implemented a new VSAN and examined the F-mode trunks connecting an upstream switch. The engineer noticed that the new VSAN is stuck in initializing.
Which two options explain why this is happening? (Choose two.)

A.    The new VSAN has not been configured in the upstream switch.
B.    A device has not attempted to log in to the new VSAN across the trunk.
C.    Only the primary VSAN lists as active while subordinate VSANs stay initializing.
D.    The trunk must be disabled and re-enabled to join the new VSAN.
E.    Only the secondary VSAN lists as active while primary VSANs stay initializing.

Answer: AB

QUESTION 124
An administrator connected a new server to a Cisco MDS 9222i on Port FCL/20, but did not capture the world wide node name of the host bus adapter.
Which command returns the needed information?

A.    show flogi database
B.    show fcns database
C.    show fcs database
D.    show wwn status
E.    show interface fc 1/20

Answer: A

QUESTION 125
An engineer is configuring a new MDS switch. The switch is powered on, the customer connects to the console, and the initial setup script is started.
Which two items can be configured during this setup process? (Choose two.)

A.    default switchport interface state
B.    default zone mode
C.    default port-channel mode
D.    default storage VDC
E.    default port VSAN membership

Answer: AB

QUESTION 126
A customer requires two separate physical pathways between multiple initiators and multiple targets. Which technology meets this requirement on a single Cisco MDS9148 switch?

A.    VSANs
B.    port security
C.    LUN masking
D.    zoning

Answer: A

QUESTION 127
Which two configuration elements are selected during initial setup are unique to Cisco MDS 9000 series Fibre Channel switches? (Choose two.)

A.    Time and Date
B.    Management IP address
C.    Default Zoneset distribution
D.    Enforce password complexity
E.    Default switchport mode F

Answer: CE

QUESTION 128
A UCS administrator has been tasked with creating a new server profile.
What two pools can be used to assign Layer 2 interface information? (Choose two.)

A.    Mac Address
B.    UUID
C.    WWN
D.    IP address
E.    Server

Answer: AC

QUESTION 129
An engineer has been asked to configure the Nexus 1000v for a ESXi Cluster.
What component of the Nexus 1000v needs to be installed on the hosts?

A.    VSG
B.    VEM
C.    vShield
D.    DVS

Answer: B

QUESTION 130
What two options are necessary to complete the installation of the Nexus 1000v Virtual Supervisor Module? (Choose two.)

A.    VLAN addresses
B.    NTP server address
C.    VSM management IP address
D.    Domain ID
E.    DNS server address

Answer: CD

QUESTION 131
What two fields must be filled out to complete the installation of the Nexus 1000v virtual switching environment? (Choose two.)

A.    Domain ID
B.    Telnet Server
C.    Administrator Password
D.    TFTP Server
E.    SNMP Community String

Answer: AC

QUESTION 132
Which two installation models are supported by Cisco virtual interfaces? (Choose two.)

A.    pass-through switching
B.    hypervisor controlled
C.    native switching
D.    channeled uplink
E.    store-and-forward switching

Answer: AB

QUESTION 133
For which task is the hypervisor responsible in a virtualized server environment?

A.    controls physical hardware resources
B.    migrates virtual machines via vMotion
C.    correlates traffic between physical servers
D.    installs virtual machine operating systems

Answer: A

QUESTION 134
Which two benefits are achieved by server virtual machines when compared to traditional computing hardware deployments? (Choose two.)

A.    server isolation
B.    increased hardware utilization
C.    reduced server configuration
D.    decreased bandwidth
E.    single management interface

Answer: AB

QUESTION 135
A customer VMware environment contains five hosts running ESXi 5.5. In addition, the environment contains a single vCenter host using standard networking. The customer wants to deploy a Cisco Nexus 1000v solution using Layer 3 mode into the environment.
Which three steps must the customer take to achieve this goal? (Choose three.)

A.    Deploy two VSM modules.
B.    Create a vmkernel interfaces on each host.
C.    Create port profiles on the VSM.
D.    Register the vCenter plugin on the 1000v.
E.    Deploy five VSM modules.
F.    Create port profiles on each host.
G.    Create a vmkernel interface on each VSM module.
H.    Register the VEM modules with vCenter.

Answer: ABC

QUESTION 136
What two chassis discovery policy settings will allow for UCS chassis to be connected to a pair of Fabric Interconnect using only two physical connections? (Choose two.)

A.    4-link
B.    2-link
C.    8-link
D.    1-link
E.    Platform-max

Answer: BD

QUESTION 137
What option automatically performs an inventory and deep discovery of any subsequently attached equipment, without requiring manual intervention?

A.    UCS Manager
B.    UCS Server
C.    CDP Manager
D.    Enterprise Manager

Answer: A

QUESTION 138
An engineer is configuring the UCS Fabric Interconnects for network connectivity to the data center LAN and SAN.
What two ports types need to be configured to allow traffic to flow properly? (Choose two.)

A.    Ethernet uplink
B.    server
C.    appliance
D.    Fibre Channel uplink
E.    Fibre Channel storage

Answer: AD

QUESTION 139
What option should be verified before configuring UCSM?

A.    verify physical connection on fabric interconnect
B.    verify Default Gateway
C.    verify DNS Server
D.    verify VLAN Configuration

Answer: A

QUESTION 140
A network engineer needs to add four native Fibre Channel ports to a pair of UCS fabric interconnects. What two items would be the result of the engineer configuring four universal ports in the fabric interconnect expansion card for storage mode and selecting apply? (Choose two.)

A.    The fabric interconnect port module reboots.
B.    The fabric interconnect reboots.
C.    The ports immediately transition to storage ports.
D.    The ports are reconfigured as Fibre Channel storage ports.
E.    The ports are reconfigured as Fibre Channel host adapter ports.

Answer: AD

Lead2pass are committed on providing you with the latest and most accurate 640-916 exam dumps. Our 640-916 dump is rich in variety. We offer 640-916 PDF dumps and 640-916 VCE dumps. We ensure you can pass the 640-916 easily. Welcome to Lead2pass.com.

640-916 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDd252MVQ5dGl0Smc

2016 Cisco 640-916 exam dumps (All 191 Q&As) from Lead2pass:

http://www.lead2pass.com/640-916.html [100% Exam Pass Guaranteed]